Plumber's Essentials: Your Key to Bathtub Installation
Plumber's Essentials: Your Key to Bathtub Installation
Blog Article
We've come across the article about How to Install a Bathtub Yourself below on the web and felt it made perfect sense to relate it with you here.
Installing a bathtub isn't exactly rocket science, however it does need strong plumbing, woodworking, and also occasionally, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably difficult task. If the old bathtub is easily available, the project can relocate speedily; if you need to open a wall surface to get rid of the old bathtub and also position the new bath tub, the task is a lot harder. In either situation, the job is within a residence handyman's skills, although you will require a helper to move out the old tub and also set in the brand-new one. Make certain you have actually qualified yourself for the job and are comfortable trying it. Rather than hiring a specialist to take control of a halfway-completed job, it is better to think about utilizing one before you start. Chances are you might require a specialist plumber to make tube links.
This write-up will certainly aid you set up a new bathtub in your restroom if you have already bought a new tub and also do not need to alter the arrangement of your previous water supply pipes.
Your devices and product checklist need to consist of the following:
Preparing for the Setup
First of all, the sustaining framework provided with the bathroom should be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to make certain that if the faucet includes a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps system to avoid strain on the bathtub.
Fit the versatile tap adapters to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its final position.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, then the first thing you must do is detach the water. After doing so, activate the faucets to drain pipes any water continuing to be in the system. The process of eliminating the existing taps can be fairly troublesome as a result of the restricted accessibility that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a fabric ready for the staying water that will certainly originate from the pipes. When the supply pipelines have actually been removed, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old sealing substance.
Prior to moving on to fit the new faucets, contrast the pipeline links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Setting up the Tub
Utilizing the two wood boards under its feet, put the tub in the required placement. The wooden boards are valuable in evenly spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto 4 little points.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by checking the level and changing the feet on the bath tub until the level reads level.
To set up taps, fit the bottom of the furthest versatile tap connector to the suitable supply pipe by making a compression join; then do the very same for the various other faucet.
Turn on the water system as well as inspect all joints and new pipework for leakages as well as tighten them if required. Fill the bath tub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Finally, deal with the bathroom paneling as explained in the maker's instruction manual. Tiling and also sealing around the tub needs to wait till the bath tub has actually been utilized at least when as this will settle it right into its last position.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will require a plastic port to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and also the other end provides a link to the current supply pipelines.
If you require to fit a monobloc, then you will call for lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the installing opening in the bath/basin guaranteeing that the washing machines are in location in between the faucet and the sink. Safeguard the tap in place with the producer given backnut. As soon as the tap is securely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal tap connectors. The former type must be attached to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bath satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to split a stiff seal, causing the water to penetrate the wall surface in between the bath as well as the tiling, resulting in complications with moisture and feasible leaks to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components as well as installations. They are marketed in tubes and cartridges, as well as can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water prior to sealing, to permit the movement experienced when the tub remains in use. The sealer can break rather very early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also easily offered on the market. It is a good idea to fit the tiles making use of water-resistant or waterproof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very taken with Tools You Need to Install a New Bathtub and I really hope you enjoyed reading the entire blog posting. Do you know somebody who is very much interested in the topic? Why not promote it. I praise you for your time. Come back soon.
Ready to help! Report this page